dimensions: [mm] properties value unit tol. pitch p 22.5 mm 0.5 length l 26 mm 1.5 height h 16.5 mm 1 width w 7 mm 1 pin diameter ? f 0.8 mm 0.05 pin hole diameter ? f 1.1 mm 0.05 pin length g 4 mm 0.5 pitch p 22.5 mm 0.5mm recommended hole pattern: [mm] schematic: properties test conditions value unit tol. capacitance 1 v/ 1 khz 0.2 khz c 1.5 f 5% rated voltage u r 250 v (dc) insulation resistance 1 min @ 100 v (dc) r iso 10000 x f min. dissipation factor @ 1 khz df 0.1 % max. dissipation factor @ 10 khz df 0.4 % max. dissipation factor @ 100 khz df 3.4 % max. rate of voltage rise dv/dt 61 v/s max. dielectric strength pin to pin 1 min @ 100 v (dc) 375 v (dc) dielectric strength pin to case 5 sec. 500 v (dc) esr @ 100 khz r esr 29.72 m typ. electrical properties: general purpose; wound type; boxed; mkp-metallized polypropylene storage conditions 5-35 c, < 75% rh operating temperature -40 c up to +105 c maxium selfheating (rated) 7 c test conditions of electrical properties: +20c, 33% rh if not specified differently fit according to separate documentation component conform to reach and rohs requirements and standards general information: wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-ftbp film capacitors mppp225155j250dcpb45004 order code 890273326007CS size revision status date (yyyy-mm-dd) business unit page pitch 22.5 002.000 pcn 2017-12-20 eicap 1/7 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. p l h w g o f p o f
1 st line right matchcode: ftbp 2 nd line right rated voltage: 250 v 2 nd line left capacitance & tolerance code: 155 j (basis pf) top cover marking p < 15 date code: yww top cover marking p 15 date code & capacitance & tolerance code product marking: properties test conditions file lead diameter [mm] force [n] condition termination robustness iec 600668 - 2 - 21 pull test 0.5 to 0.8 10 min. 10 sec. 0.9 to 1.25 20 min. 10 sec. bend test 0.5 to 0.8 5 min. 2 cycles 0.9 to 1.25 10 min. 2 cycles mechanical properties properties standard vibration iec 60068 - 2 - 6 all 3 directions, 2 hours each @ 15 - 55 - 15 hz, amplitude 0.75 mm or 10 g damp heat iec 60068 - 2 - 78 40c, 95% rh, 56 days temperature cycles iec 60068 - 2 - 14 5 cycles, upper and lower temperature 30 min. each, 30 sec. transfer time environmental tests: capacitance change vs. temperature: wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-ftbp film capacitors mppp225155j250dcpb45004 order code 890273326007CS size revision status date (yyyy-mm-dd) business unit page pitch 22.5 002.000 pcn 2017-12-20 eicap 2/7 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. -5.0% -3.0% -1.0% 1.0% 3.0% 5.0% -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 105 capacitance change [%] temperature [ c]
dissipation factor vs. temperature: rated voltage vs. temperature: wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-ftbp film capacitors mppp225155j250dcpb45004 order code 890273326007CS size revision status date (yyyy-mm-dd) business unit page pitch 22.5 002.000 pcn 2017-12-20 eicap 3/7 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. 0.000% 0.020% 0.040% 0.060% 0.080% 0.100% -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 105 dissipation factor [%] temperature [ c] 0.0% 20.0% 40.0% 60.0% 80.0% 100.0% 120.0% -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 105 rated voltage / max voltage [%] temperature [ c]
packaging specification - carton: [mm] l ic (mm) w ic (mm) h ic (mm) no. of paperboard no. of layer packaging unit material typ. typ. typ. pcs. pcs. pcs. 275,00 160,00 95,00 5 4 912 paper l c (mm) w c (mm) h c (mm) no. of inner carton packaging unit material typ. typ. typ. pcs. pcs. 500,00 290,00 240,00 6 5472 paper wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-ftbp film capacitors mppp225155j250dcpb45004 order code 890273326007CS size revision status date (yyyy-mm-dd) business unit page pitch 22.5 002.000 pcn 2017-12-20 eicap 4/7 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. w i c l i c h ic paperboard h c l c w c
classification wave soldering profile: profile feature pb-free assembly sn-pb assembly preheat temperature min t s min 100 c 100 c preheat temperature typical t s typical 120 c 120 c preheat temperature max t s max 130 c 130 c preheat time t s from t s min to t s max t s 70 seconds 70 seconds ramp-up rate t 150 c max. 150 c max. peak temperature t p 250 c - 260 c 235 c - 260 c time of actual peak temperature t p max. 10 seconds max. 5 seconds each wave max. 10 seconds max. 5 seconds each wave ramp-down rate, min ~ 2 k/ second ~ 2 k/ second ramp-down rate, typical ~ 3.5 k/ second ~ 3.5 k/ second ramp-down rate, max ~ 5 k/ second ~ 5 k/ second time 25c to 25c 4 minutes 4 minutes classification wave soldering profile: refer to en61760-1:2006 wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-ftbp film capacitors mppp225155j250dcpb45004 order code 890273326007CS size revision status date (yyyy-mm-dd) business unit page pitch 22.5 002.000 pcn 2017-12-20 eicap 5/7 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance. temperature time t p t p t s max t s typical t s min first wave preheat area cool down area second wave typical temperature procedure min temperature procedure max temperature procedure
cautions and warnings: the following conditions apply to all goods within the product series of wcap-ftbp of wrth elektronik eisos gmbh & co. kg: 1. general: the capacitor is engineered, designed and manufactured to be used within the datasheet specified values. do not use the capacitor neither short term nor long term outside the specified values, which are given in the data sheet. 2. product specific: follow all instructions mentioned in the data sheet, especially: ? the soldering profile has to be complied with according to the technical reflow soldering specification, otherwise this will void the warranty. ? wave soldering is only allowed after evaluation and approval. ? do not exceed the lower and/ or upper specified temperature! ? do not use the capacitor with other than specified voltage! ? prevent any kind of mechanical stress to the capacitor terminals! ? do not use the soldered capacitor on a pcb for any movement or transportation to avoid any tensile force to the capacitor! ? do not apply any kind of flexural or compressive force onto soldered or unsoldered component! ? prevent the capacitor surface from any damage or scratches with sharp edges (e.g. chassis, screwdrivers, pincers). ? the capacitor must be placed on a pcb while using the recommended drill hole pattern without changing of the specific lead pitch! ? avoid any other than specified temperature and / or time conditions during soldering! ? avoid any overload or conditions that are not specified in the capacitors datasheet! ? avoid any water or heavy dust on capacitors surface which may cause electrical leakage, damage, overheating or corrosion! 3. storage conditions: these film capacitors must be stored in stable climatic conditions, which are listed within the general information on front of data sheet. 4. storage duration: all products shall be used before the end of the period of 12 months based on the product date code, if not a 100% solderability cant be ensured. 5. flammability: avoid any external energy or open fire (passive flammability). 6. vibration resistance: do not exceed the vibration limits given by iec60068-2-6. 7. cleaning: do not use any other cleaning solvents for box-typed capacitors except: ethanol, isopropanol, n-propanol - water mixtures. after cleaning a drying process with temperatures not exceeding 65c and not longer than 4 hours is mandatory to prevent any kind of electrical damage. 8. full covered or embedded capacitors in final applications: if final assemblies will be placed completely in any plastic resin, physical, chemical and thermal influences must be considered. if any specific evaluation or test is necessary please contact the related wrth elektronik capacitor business division. wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-ftbp film capacitors mppp225155j250dcpb45004 order code 890273326007CS size revision status date (yyyy-mm-dd) business unit page pitch 22.5 002.000 pcn 2017-12-20 eicap 6/7 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
important notes the following conditions apply to all goods within the product range of wrth elektronik eisos gmbh & co. kg: 1. general customer responsibility some goods within the product range of wrth elektronik eisos gmbh & co. kg contain statements regarding general suitability for certain application areas. these statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. the responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not. 2. customer responsibility related to specific, in particular safety-relevant applications it has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications. in certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. therefore, customer is cautioned to verify that data sheets are current before placing orders. the current data sheets can be downloaded at www.we-online.com. 3. best care and attention any product-specific notes, cautions and warnings must be strictly observed. any disregard will result in the loss of warranty. 4. customer support for product specifications some products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. necessary information is available on request. in this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter. 5. product r&d due to constant product improvement product specifications may change from time to time. as a standard reporting procedure of the product change notification (pcn) according to the jedec-standard inform about minor and major changes. in case of further queries regarding the pcn, the field sales engineer or the internal sales person in charge should be contacted. the basic responsibility of the customer as per section 1 and 2 remains unaffected. 6. product life cycle due to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. as a standard reporting procedure of the product termination notification (ptn) according to the jedec-standard we will inform at an early stage about inevitable product discontinuance. according to this we cannot guarantee that all products within our product range will always be available. therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. the approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 7. property rights all the rights for contractual products produced by wrth elektronik eisos gmbh & co. kg on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with wrth elektronik eisos gmbh & co. kg. wrth elektronik eisos gmbh & co. kg does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which wrth elektronik eisos gmbh & co. kg components or services are used. 8. general terms and conditions unless otherwise agreed in individual contracts, all orders are subject to the current version of the general terms and conditions of wrth elektronik eisos group, last version available at www.we-online.com. wrth elektronik eisos gmbh & co. kg emc & inductive solutions max-eyth-str. 1 74638 waldenburg germany tel. +49 (0) 79 42 945 - 0 www.we-online.com eisos@we-online.com created checked general tolerance projection method kas psl din iso 2768-1m description technical reference wcap-ftbp film capacitors mppp225155j250dcpb45004 order code 890273326007CS size revision status date (yyyy-mm-dd) business unit page pitch 22.5 002.000 pcn 2017-12-20 eicap 7/7 this electronic component has been designed and developed for usage in general electronic equipment only. this product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. moreover wrth elektronik eisos gmbh & co kg products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. wrth elektronik eisos gmbh & co kg must be informed about the intent of such usage before the design-in stage. in addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.
|
